Snapper Pro Rider 75 Series Fit and Snapper 2011 Stand-On Fit
with RB-DP Bracket
Multi-Mount Stainless Steel/Aluminum Catcher
See Catcher Fits, Installation and Instructional Videos Below
- Stainless Steel/Aluminum Hybrid Grass Catcher is designed to be lightweight yet strong, durable and versatile to provide years of trouble free service
- Our Hybrid Grass Catcher is designed to accept a mower specific face plate, so if you ever sell your mower all you would need to do is buy a new face plate for the catcher that will fit your new machine
- 4.4 cubic foot capacity
- Multi-Mount Stainless Steel/Aluminum Catchers have an extended face plate mount which extends out from the catcher surface 7/8 ths of an inch. In the past, if you had a deck that did not stick out farther than the rear wheel, catchers would not work because they would rub the rear wheel. The extended face plate mount on the RC-MMS-4 will clear the rear wheel. The extension is 7/8” so it will work on most decks where this was a problem, but not all. Check the measurements on your specific mower
- Hinged Swing Door
- Comes with 1 designated face plate
If you cannot find the correct fit for your machine, text a photo of your mower's discharge opening (with chute up and tape measure for reference) to 570-994-8298 to confirm the catcher fit, since manufacturers can change a deck configuration a couple of times a year. This can cause the catcher fit to change. A reply will be sent by text.
**You will be responsible for the return shipping costs if you did not call to confirm the correct catcher fit**
NOTE: Please see our Multi-Mount Catcher Application Chart to determine which Multi-Mount Catcher you will need for your mower.
Additional required brackets are noted
This catcher fits:
Ariens - 36"
Ariens - Gear Drive Walk Behind 36" 2009 & after
Ariens - Husky 36"
Ariens - Pro Zoom Stand-on
Big Dog - T Series Walk Behind 36, 48 & 54" (must remove plate)
Cub Cadet - Gear series
Cub Cadet - Tank Rider L48 48"
Cub Cadet - Walk Gear G-1236
Cub Cadet - Walk Gear G-1548
Cub Cadet - Z Force Rider 48, 52 & 60"
Everride - 36"
Ferris - 36, 48" & 52"
Ferris - 52 & 61" (depends on year and size, Catcher opening is 14 3/4 x 4")
Ferris - Comfort Control DD Walk Behind 36"
Ferris - Comfort Control Walk Behind 52"
Ferris - Evolution Rider 36, 48 & 52" - Requires RB-DP bracket
Ferris - Hydro Cut Walk Behind 36" (must remove plate)
Ferris - IS Series 36", 48" & 52" - Requires RB-DP bracket
Ferris - SRSZ2 Stand on ZTR 52"
Gravely - Pro 150 Pro 36"
Gravely - Pro Walk Behind
Gravely - Pro Walk Behind 36G 48H & 61H
Gravely - Stand-on Pro Stance 52"
Hustler - Fastrak Rider 48 & 60"
Hustler - Fastrak Rider 54" (must remove plate)
Hustler - Trim Star Walk Behind 36, 48 & 54" 2008 - 2012
John Deere - G15 - Requires RB-DP bracket
John Deere - 657 7 Iron II
John Deere - 657 Quik Trak 54"
John Deere - Walk Behind WG-32A
John Deere - Walk Behind WG-36A
John Deere - Walk Behind WG-48A
John Deere - Walk Behind WH-48A
John Deere - Walk Behind WH-52A
Kubota - ZG Series Rider 48 & 52" - Requires RB-DP bracket
Kubota - ZG 227 - Requires RB-DP bracket
Scag Flat Nose Regular Deck 32, 36, 48 & some 52" (check discharge opening)
Scag - Freedom Rider 36" & 48" 2009
Scag - Freedom Rider 48", 52" & 61" - Bracket RB-DP required
Scag - Liberty Rider 2016 52"
Scag - Walk Behind Zero Turn SWZT 36
Simplicity - Citation Rider 52" - Requires RB-DP bracket
Simplicity - Rider 48 & 52" - Requires RB-DP bracket
Snapper - Pro 2011 Stand-on - Requires RB-DP bracket
Snapper - Pro 32" Walk Behind
Snapper - Pro Rider 75 Series - Requires RB-DP bracket
Snapper - S-50 Rider
Snapper - Pro SW Walk Behind Series
The mower's discharge opening MUST stick out farther then the rear wheel of the mower.
If the discharge does NOT stick out farther then the rear wheel our catcher will NOT fit.